Let's Connect :
support@wonderpaints.com
LUXE SERIES : Nexa HD Exterior Emulsion
Nexa High-Definition, Waterproof Exterior Laminate The paint coating is ultra-smooth, impervious to dirt and water, and created using cutting-edge technology. Laminate that is impervious to dust and liquids
The coating of paint seals up all the microscopic holes, making the surface impermeable to water. It is also very resilient against the damaging effects of ultraviolet radiation.
Performance Features & Benefits
- DIRT proof film: Nano particle technology that is one of a kind
- Waterproof film has a great ability to stretch to cover small cracks.
- It lets water vapor through well: the coating is breathable and sticks to masonry very well.
- High sheen: for a glow and elegance that lasts.
Great protection from UV rays, so colors don’t fade. - Excellent Anti fungal / Anti Algae protection and Alkali resistance
Application Details & Surface Preparation
Mixing
Stir well & stain before use
Tools
Brush, Roller & Spray gun
Thinning
Water
Thinning Ratio
Brush Application: 40% by Volume Roller Application: 10-15 by Volume
Surface Drying Time
Surface Dry in 30 Min
Filing
Wonder paints Polymer Putty or Acrylic Wall Putty
Application Environment
Temperature: 10-40 Degree celcius. Humidity below 80%
Safety Features
Non-flammable, No added lead, mercury or Chromium compounds
Cleaning
Clean the surface of loose paint, dust & grease.
Sand using emery paper & wipe clean using soft cloth & water.
Allow to dry.
Surface preparation
Apply the Cement Primer. Allow it to dry.
Fill holes in the surface with two coats of wonder paint Acrylic Wall Putty.
Let it dry and apply one more
coat of WT Cement primer. Allow it to dry.
Application
Apply two or three coats of wonder LUXURA INTERIOR EMULSION which you can get by mixing 1 L of emulsion with 400 ml of water with a brush or 150 ml of water with a roller. Give each coat 4-6 hours to dry in between
Data Visualization
- Coverage : 1 Coat: 15-16 sqm/L*. 2 Coats: 7-8 sqm/L*
- Drying : Time 4-6 hours
- Sheen Level : 15 @ 60 degree
- Flash Point : NA
- Stability of thinned paint : 24 hours
- Appearance : Smooth White Liquid
- Solids : 55%
- Specific Gravity : 1.3
- Recommended DFT : NA
- Viscosity : 1700 CP @ 30°C by stormer viscometer
- Shelf Life : 36 months
- Contrast ratio : 98%
- Wall should be dry and fresh plaster cured for 4 weeks.
- Before painting, fix leaks and cracks.
- Avoid applying to lime-washed surfaces.
- Dark hues demand a second coat.
- Apply one layer of Wonder Paints WB Sealer Primer before painting efflorescent walls.
- Remove masking tape from painted areas before the paint film dries.
For the best results, clean the walls every 6 months to get rid of any dirt, dust, or grease that has built up.
The dirt and grime hold things down and help algae
and fungi grow.
Available in : 1L, 4L, 10L, 20L
As per Wonder Paints Color Fan Deck
- Stir well and strain before use.
- Do not apply paint when ambient temperature is below 10°C or higher than 45°C or there are chances of such temperature within 4 hours of application.
- Ensure the surface/walls to be painted has dried properly. For new surfaces ensure the plastered walls have cured for 6-8 weeks before painting. Remove loose / flaky paint
- Use a pressure washer and wire brush to get rid of all traces of algae, fungus, dust, and dirt. For the new coating to last longer, it is important that all traces of ontaminants are taken care of properly. After a thorough cleaning, a bio wash will need to be used in places where there is a lot of algae growth.
- Cracks to be sealed. Non-structural cracks can be sealed using a good quality crack seal. For structural cracks take the advice of a Structural engineer.
- Check for efflorescence (white dust on rubbing the wall with your hand). If present should be treated with an anti-e ores- cence primer like Wonder Paints WT Sealer Primer. If this is not treated then the new coating being applied will have inferior adhesion.
- Make sure that a tinting machine and machine colorants from wonder Paints were used to make the shade you chose. Make sure that colored paints are thoroughly mixed.
- Ensure painting is completed before rains. Exposing primer coat or primer coat plus one topcoat to the rain will adversely affect the performance of paint system.
- Always ensure three coats of the topcoat on sunshades and horizontal surfaces. Also ensure the horizontal surfaces are coated first before the vertical to avoid streak marks.
- Do not overthin the paint. And always use good quality water for thinning, chlorinated water is not recommended.
- Thinned paint must be consumed within 24 hours of dilution, after which there are high chances of bacterial growth.
- When using colours that have been tinted in different batches of any emulsion, it is always advisable to mix the batches together and then apply the colour at site. There may be very small variations in colour between batches and this may be more evident when applied side by side or during touch up.
- Dark colours in emulsions are tinted using clear bases, hence the hiding of these shades will be inferior when compared to lighter shades (shades tinted in the first base). Such dark shades may require three-four coats, without dilution, to ensure proper hiding OR the primer will have to be tinted in this shade, followed by two-three coats for proper hiding.
- Only fine (using less pressure) sanding should be done over Polymer Putty & Waterproof Polymer Putty, using abrasive paper grit no.120 or higher. Sanding using rough emery paper or high pressure will break the polymer film formed & lead to adhe- sion/water repellancy issues.
- Paint should not be applied as a thick coat, especially in corners
- Stir well and strain before use.
- Do not apply paint when ambient temperature is below 10°C or higher than 45°C or if there are chances of such temperature within 4 hours of application.
- Ensure the surface/walls to be painted has dried properly. For new surfaces ensure the plastered walls have cured for 6-8 weeks before painting.
- Sources of leak must be identified, fixed and allowed to dry completely before painting.
- During repainting, all loose, flaky material must be removed and the walls cleaned before application of fresh paint.
- Sheen emulsions have a tendency to reflect light, hence the surface must ideally be free of undulations to the extent possible for best results. Otherwise, all the undulations/uneven areas in the wall will be highlighted when light reflects off the wall.
- In case of Premium, Luxury emulsions and Acrylic Laminate, if masking tape is used to separate the areas being painted then the masking tape must be removed immediately after application, when the paint is still wet. Else there are chances of the paint peeling off along with the tape.
- Always ensure primer is applied over putty before application of the topcoat. This will ensure a more even finish and also improve coverage of the topcoat.
- Ensure that Wonder Paints tinting machine and machine colourants have been used to produce the shade selected. Ensure that tinted paints are mixed thoroughly.
- When using colours that have been tinted in different batches of any emulsion, it is always advisable to mix the batches together and then apply the colour at site. There may be very small variations in colour between batches and this may be more evident when applied side by side or during touch up.
- If unused paint is to be stored, then it must be not be diluted with water. It must be stored in an undiluted condition in an air tight container and kept in a cool and dry space. If the emulsion has been diluted with water, then it must be used within 24 hours.
- Dark colours in emulsions are tinted using clear bases, hence the hiding of these shades will be inferior when compared to lighter shades (shades tinted in the first base). Such dark shades may require three-four coats, without dilution, to ensure proper hiding OR the primer will have to be tinted in this shade, followed by two-three coats for proper hiding.
- Only fine (using less pressure) sanding should be done over Polymer Putty & Waterproof Polymer Putty, using abrasive paper grit no. 120 or higher. Sanding using rough emery paper or high pressure will break the polymer film formed & lead to adhesion/water repellancy issues.
- Paint should not be applied as a thick coat, especially in corners
Head Office
Contact us
Locations
- Manufacturing : Wonder Paints Pvt. Ltd., 218, IID Centre, Kaladwas, Udaipur, Rajasthan 313003, India.
- Head Office : Wonder Paint House, Siddhachal Giri Apartment, Ashok Nagar, Kandivali (E).
- Corporate Office : Orion point, 7 Crews Street, E143TU, London (UK).
Wonder Paints Pvt. Ltd. © All Rights Reserved – 2024.
Developed By Barcadly Services