Let's Connect :
support@wonderpaints.com
LUXE SERIES : Vintage Dual Emulsion
Vintage Dual Emulsion Pure acrylic ensures a durable, glossy appearance. It may be used on either indoor or outdoor surfaces.
Performance Features & Benefits
- Anti-fungal and anti-algal properties
- High stain resistance
- A lustrous sheen finish (For Interior Surfaces)
- Easy to clean ( for interior and exterior )
Application Details & Surface Preparation
Mixing
Stir well & stain before use
Tools
Brush, Roller & Spray gun
Thinning
Water
Thinning Ratio
Brush Application: 40% by Volume Roller Application: 10-15 by Volume
Surface Drying Time
Surface Dry in 30 Min
Filing
Wonder paints Polymer Putty or Acrylic Wall Putty
Application Environment
Temperature: 10-40 Degree celcius. Humidity below 80%
Safety Features
Non-flammable, No added lead, mercury or Chromium compounds
Cleaning
Clean the surface of loose paint, dust & grease.
Sand using emery paper & wipe clean using soft cloth & water.
Allow to dry.
Surface preparation
Apply the Cement Primer. Allow it to dry.
Fill holes in the surface with two coats of wonder paint Acrylic Wall Putty.
Let it dry and apply one more
coat of WT Cement primer. Allow it to dry.
Application
Apply two or three coats of wonder LUXURA INTERIOR EMULSION which you can get by mixing 1 L of emulsion with 400 ml of water with a brush or 150 ml of water with a roller. Give each coat 4-6 hours to dry in between
Data Visualization
- Coverage : 1 Coat : FOR INTERIOR FOR EXTERIOR 19-20 sqm/L* and FOR EXTERIOR 12-14 sqm/L* *
- Coverage : 2 Coat : FOR INTERIOR FOR EXTERIOR 12-14 sqm/L* and FOR EXTERIOR 6-7 sqm/L*
- Drying : Time 4-6 hours
- Sheen Level : 22 @ 60 degree
- Flash Point : NA
- Stability of thinned paint : 4-6 hours
- Appearance : Smooth white Liquid
- Solids : 49%
- Specific Gravity : 1.24
- Recommended DFT : NA
- Viscosity : 2200 CP @ 30°C by stormer viscometer
- Shelf Life : 36 months
- Contrast ratio : 97%
- The wall should be dry, and it should take 4 weeks for the
new plaster to harden. - Fix any leaks or cracks before you point.
- Make sure that all algae and fungi are gone before you
point. For the best protection, horizontal areas like ledges
and sunshades will need an extra coat. - Paint should only be put on a surface that is dry and never
when it is raining
For the best results, clean the walls every 6 months to
get rid of any dust, dirt, or grease that has built up.
The dirt and grime act as an anchor and help algae and fungi grow. For cleaning the inside of your car, use a soft sponge and a mild soap solution.
Available in : 1L, 4L, 10L, 20L
As per Wonder Paints Color Fan Deck
- Stir well and strain before use.
- Do not apply paint when ambient temperature is below 10°C or higher than 45°C or there are chances of such temperature within 4 hours of application.
- Ensure the surface/walls to be painted has dried properly. For new surfaces ensure the plastered walls have cured for 6-8 weeks before painting. Remove loose / flaky paint
- Use a pressure washer and wire brush to get rid of all traces of algae, fungus, dust, and dirt. For the new coating to last longer, it is important that all traces of ontaminants are taken care of properly. After a thorough cleaning, a bio wash will need to be used in places where there is a lot of algae growth.
- Cracks to be sealed. Non-structural cracks can be sealed using a good quality crack seal. For structural cracks take the advice of a Structural engineer.
- Check for efflorescence (white dust on rubbing the wall with your hand). If present should be treated with an anti-e ores- cence primer like Wonder Paints WT Sealer Primer. If this is not treated then the new coating being applied will have inferior adhesion.
- Make sure that a tinting machine and machine colorants from wonder Paints were used to make the shade you chose. Make sure that colored paints are thoroughly mixed.
- Ensure painting is completed before rains. Exposing primer coat or primer coat plus one topcoat to the rain will adversely affect the performance of paint system.
- Always ensure three coats of the topcoat on sunshades and horizontal surfaces. Also ensure the horizontal surfaces are coated first before the vertical to avoid streak marks.
- Do not overthin the paint. And always use good quality water for thinning, chlorinated water is not recommended.
- Thinned paint must be consumed within 24 hours of dilution, after which there are high chances of bacterial growth.
- When using colours that have been tinted in different batches of any emulsion, it is always advisable to mix the batches together and then apply the colour at site. There may be very small variations in colour between batches and this may be more evident when applied side by side or during touch up.
- Dark colours in emulsions are tinted using clear bases, hence the hiding of these shades will be inferior when compared to lighter shades (shades tinted in the first base). Such dark shades may require three-four coats, without dilution, to ensure proper hiding OR the primer will have to be tinted in this shade, followed by two-three coats for proper hiding.
- Only fine (using less pressure) sanding should be done over Polymer Putty & Waterproof Polymer Putty, using abrasive paper grit no.120 or higher. Sanding using rough emery paper or high pressure will break the polymer film formed & lead to adhe- sion/water repellancy issues.
- Paint should not be applied as a thick coat, especially in corners
- Stir well and strain before use.
- Do not apply paint when ambient temperature is below 10°C or higher than 45°C or if there are chances of such temperature within 4 hours of application.
- Ensure the surface/walls to be painted has dried properly. For new surfaces ensure the plastered walls have cured for 6-8 weeks before painting.
- Sources of leak must be identified, fixed and allowed to dry completely before painting.
- During repainting, all loose, flaky material must be removed and the walls cleaned before application of fresh paint.
- Sheen emulsions have a tendency to reflect light, hence the surface must ideally be free of undulations to the extent possible for best results. Otherwise, all the undulations/uneven areas in the wall will be highlighted when light reflects off the wall.
- In case of Premium, Luxury emulsions and Acrylic Laminate, if masking tape is used to separate the areas being painted then the masking tape must be removed immediately after application, when the paint is still wet. Else there are chances of the paint peeling off along with the tape.
- Always ensure primer is applied over putty before application of the topcoat. This will ensure a more even finish and also improve coverage of the topcoat.
- Ensure that Wonder Paints tinting machine and machine colourants have been used to produce the shade selected. Ensure that tinted paints are mixed thoroughly.
- When using colours that have been tinted in different batches of any emulsion, it is always advisable to mix the batches together and then apply the colour at site. There may be very small variations in colour between batches and this may be more evident when applied side by side or during touch up.
- If unused paint is to be stored, then it must be not be diluted with water. It must be stored in an undiluted condition in an air tight container and kept in a cool and dry space. If the emulsion has been diluted with water, then it must be used within 24 hours.
- Dark colours in emulsions are tinted using clear bases, hence the hiding of these shades will be inferior when compared to lighter shades (shades tinted in the first base). Such dark shades may require three-four coats, without dilution, to ensure proper hiding OR the primer will have to be tinted in this shade, followed by two-three coats for proper hiding.
- Only fine (using less pressure) sanding should be done over Polymer Putty & Waterproof Polymer Putty, using abrasive paper grit no. 120 or higher. Sanding using rough emery paper or high pressure will break the polymer film formed & lead to adhesion/water repellancy issues.
- Paint should not be applied as a thick coat, especially in corners
Head Office
Send Message
Locations
- Manufacturing : Wonder Paints Pvt. Ltd., 218, IID Centre, Kaladwas, Udaipur, Rajasthan 313003, India.
- Head Office : Wonder Paint House, Siddhachal Giri Apartment, Ashok Nagar, Kandivali (E).
- Corporate Office : Orion point, 7 Crews Street, E143TU, London (UK).
Wonder Paints Pvt. Ltd. © All Rights Reserved – 2024.
Developed By Barcadly Services